- (321) 390-7340
- thomaschevauhn@ax-terracor.com
- 941 GEORGIA AVENUE, ROCKLEDGE, FL 32955
Menu
Axterracor Dinnerware is 100% Made in the USA to restaurant grade standards of durability. Our dishes are vitrified and lead-free, and most glazes, including white, are cadmium-free. Please see our FAQ for more info about cadmium in our glazes.
Every single piece we manufacture – every plate, bowl, mug, cup, platter, tray, serving piece, salt and pepper shaker, butter dish, mixing bowl, sugar bowl, creamer, or ramekin – resists chipping and is microwave safe, dishwasher safe, freezer safe, oven safe and even broiler safe.
With nearly a hundred years of experience in the food service industry, you can count on Axterracor to make beautiful dishes that last, however you cook and whatever you serve.
Customer and employee safety is our top priority.
We shall be following Governor Ducey’s safety guidelines to prevent the spread of COVID-19.
Axterracor dinnerware is made 100% in Rockledge, FL USA
As a matter of fact, our entire operation, from our CEO’s office to our factory, is located under roof…so we know exactly what goes on with our manufacturing and what materials are used to create your dinnerware.
All of Axterracor ceramic pieces are lead-free. We do not put lead in any of our clay or glazes. Our ceramic pieces pass CA Prop 65 as well as FDA standards.
Most colors, including white, are cadmium-free.
The glaze colors orange and red cannot be made without cadmium. But the safety of our dinnerware is of utmost importance to us. Therefore, Axterracor only uses what is called “encapsulated cadmium”. The cadmium is encapsulated in non-toxic Zircon crystals rendering the cadmium impossible to leach out of the crystals.
Axterracor has even tested our red and orange glazed dinnerware after being used daily, by our CEO’s family of four, for 5 years. These tests, like the tests of freshly made dinnerware, also have results of “none detected”, whatsoever, for lead and cadmium.
Again, our ceramic pieces (even any pieces with orange or red glaze) have always passed CA Prop 65 and FDA standards. We actually surpass those standards as our test results show “none detected”, whatsoever, for lead and cadmium.
Axterracor dinnerware is known for its durability and longevity of use as well as its beauty.
Following these few simple guidelines will help keep your ware at its best:
Rubbing an unglazed “foot” against a glazed surface can cause surface scratches Stack with care You may want to insert a paper towel between items when nesting Do NOT use on a stove top burner Avoid impact. Handle with care Silverware marks all ceramic surfaces; the more you use your dishes, the more likely it is that you shall see grey “metal marks” on its surface. Do NOT use bleach to remove metal marks, as bleach will often leave a chalky look on your dinnerware. Scrubbing only with a scouring pad can wear down a glaze surface, thus making it more difficult to clean and easier to receive metal marks in the future
THE ANSWER to remove metal marks: We recommend a safe, reusable product called ChinaMate®. When kept filtered, the cleaner will last indefinitely, saving you money and time. Soaking dinnerware in ChinaMate® and rubbing with a Scotch-Brite™ pad effectively removes metal marks without compromising the look or surface quality of your dinnerware.
We accept WIRE and ACH transfers.
All of Axterracor ceramic pieces are lead-free. We do not put lead in any of our clay or glazes. Our ceramic pieces pass CA Prop 65 as well as FDA standards.
All of Axterracor dinnerware is made in the USA 100%… in Rockledge, FL.
As a matter of fact, our entire operation, from our CEO’s office to our factory, is located under one roof…so we know exactly what goes on with our manufacturing and what materials do and do not go into your dinnerware.
Our dinnerware is not only highly chip-resistant, but it is non-porous which eliminates “crazing” over decades of use.
With over 90 years of experience in the food service industry, our high strength material is specially made to meet the rigorous demands of this industry. We sell this exact same quality to our public consumers.
The Axterracor engineers, craftsmen, designers, hand painters, pottery workers, customer service persons, and managers are largely “home-grown” and have decades of experience.
Come experience the value and feel the difference of Axterracor dinnerware sets, plates, mugs, bowls, and more.
Many of the few US commercial dinnerware manufacturers still standing at that time have since closed or chosen to manufacture in China or other overseas countries. Dirck has invested in land, buildings, plant, equipment, and developed people in Tucson. He and his associates have worked tirelessly to create a product line that is seen by the food service industry, private labelers, and the end consumer as offering a very good value for the money, and is an excellent alternative to products made overseas.
